SASTI Smart Power Factor Correction - Enhance Energy Efficiency & Reduce Costs

SASTI SPFC SERIES

4.5

The SASTI-SPFC6MU Smart Power Factor Correction (SPFC) devices enhance electrical efficiency by dynamically adjusting the power factor using advanced technology. These devices integrate with smart grids for predictive maintenance, remote monitoring, and automated control, improving reliability and reducing energy costs. By optimizing power systems, SPFC devices lower greenhouse gas emissions and support sustainability. They offer a modern, efficient, and eco-friendly solution for managing electrical systems.

Item no:

SASTI-SPFC6MU

Color:

Grey

Brand:

SASTI

Buy now

Rated Voltage:	400V
Rated Capacity:	30~100kVAr/15~150A
Frequency Circuit:	50/60Hz±5%
Circuit Topology:	Three Level
Multi Compensation Mode:	Harmonic compensation, reactive compensation, three-phase load unbalance compensation
Filter range Rated of:	2nd~51st odd order harmonics (Selective or Full compensation)
Related Harmonic Reduction:	≥97.5% (For typical harmonic order distortions)
Filtering Performance:	Typically, THDi≤ 5% at rated load(Even with most complex loads)
Target Power Factor:	Adjustable from -1.0 to +1.0
3 Phase Load Balancing Effect:	≤5%, Mitigate negative and zero sequence
Neutral Filtering Capacity:	3 times the rated filter current(in case of 4 wire device)
3 Phase Load Balancing Effect:	≤5%, Mitigate negative and zero sequence
Neutral Filtering Capacity:	3 times the rated filter current(in case of 4 wire device)
Switching/control frequency :	25.6kHz
Initial response time:	≤50us
Overall response time:	≤5ms
Active loss of system:	≤2.5%
Output current limit :	Automatically limited within 100% of rated capacity to output
Control algorithm:	Intelligent FFT,Self-adaptive control algorithm(ADALINE), fast Fourier (FFT) and instantaneous reactive power algorithm
Controller:	DSP+FPGA
Protection:	Hardware protection, Software protection
Control connection:	Fibre or electrical connection
Human Machine Interface:	4.3’’inch/7’’inch/10’’inch touched TFT LCD HMI
Communication protocols:	Adopt Modbus RTU remote communication protocol; Communication interface adopts two channel RS485 and CAN bus, Supporting mobile phone APP operation, Accessing and monitioring via Ethernet
Noise:	<60db(<45db during low-speed operation)
Installation method:	Module embedded(Rack),wall mounted, free landing
Level of protection:	IP42
Cooling method:	Speed regulation intelligent air cooling PWM Fans
Color:	RAL 7035 Light Grey/Black
Ambient temperature:	-20~55℃
Relative humidity:	Maximum 95%, without condensation
Mounting height above sea level:	≤2000 at rated capacity; appropriately reduce the capacity if it is > 2000(1% derating per 100m)
Qaulifications:	CE, IEEE61000,Type Test Report, ISO9001:2015
Compliance with Standards:	IEEE 519, ERG5/4

Rated Voltage:

400V

Rated Capacity:

30~100kVAr/15~150A

Frequency Circuit:

50/60Hz±5%

Circuit Topology:

Three Level

Multi Compensation Mode:

Harmonic compensation, reactive compensation, three-phase load unbalance compensation

Filter range Rated of:

2nd~51st odd order harmonics (Selective or Full compensation)

Related Harmonic Reduction:

≥97.5% (For typical harmonic order distortions)

Filtering Performance:

Typically, THDi≤ 5% at rated load(Even with most complex loads)

Target Power Factor:

Adjustable from -1.0 to +1.0

3 Phase Load Balancing Effect:

≤5%, Mitigate negative and zero sequence

Neutral Filtering Capacity:

3 times the rated filter current(in case of 4 wire device)

3 Phase Load Balancing Effect:

≤5%, Mitigate negative and zero sequence

Neutral Filtering Capacity:

3 times the rated filter current(in case of 4 wire device)

Switching/control frequency :

25.6kHz

Initial response time:

≤50us

Overall response time:

≤5ms

Active loss of system:

≤2.5%

Output current limit :

Automatically limited within 100% of rated capacity to output

Control algorithm:

Intelligent FFT,Self-adaptive control algorithm(ADALINE), fast Fourier (FFT) and instantaneous reactive power algorithm

Controller:

DSP+FPGA

Protection:

Hardware protection, Software protection

Control connection:

Fibre or electrical connection

Human Machine Interface:

4.3’’inch/7’’inch/10’’inch touched TFT LCD HMI

Communication protocols:

Adopt Modbus RTU remote communication protocol; Communication interface adopts two channel RS485 and CAN bus, Supporting mobile phone APP operation, Accessing and monitioring via Ethernet

Noise:

<60db(<45db during low-speed operation)

Installation method:

Module embedded(Rack),wall mounted, free landing

Level of protection:

IP42

Cooling method:

Speed regulation intelligent air cooling PWM Fans

Color:

RAL 7035 Light Grey/Black

Ambient temperature:

-20~55℃

Relative humidity:

Maximum 95%, without condensation

Mounting height above sea level:

≤2000 at rated capacity; appropriately reduce the capacity if it is > 2000(1% derating per 100m)

Qaulifications:

CE, IEEE61000,Type Test Report, ISO9001:2015

Compliance with Standards:

IEEE 519, ERG5/4

SASTI SPFC Series

SASTI SPFC SERIES

Cost Effective:

Advanced Networks Performance:

SPFC in Power Distribution

SPFC in Renewable Energy Integration

SPFC in Substations

To Know More